12/17/2023 0 Comments Hans solo frozen in carboniteHow Long Was Han Solo Frozen In Carbonite? That’s how Han Solo, still frozen in carbonite, ended up on Tatooine, where he thawed out of the carbonite in Return of the Jedi, happening around 4 ABY. After Vader was done with Solo, Fett took the bounty, and Solo to collect another bounty on him, as Jabba the Hutt offered a hefty amount of dough for anyone who brought Han Solo to him alive. The capture happened in The Empire Strikes Back, which happened around 3 ABY. I chose a lighter grey here to add a bit of contrast with the darker part where Han is frozen.Why Is Lando Wearing Han’s Clothes in The Empire Strikes Back? After that, I lightly pressed painters tape over the painted section, and proceeded to paint the rest of the side. I also cut flaps that I could open on the inside to press the LED lights I bought at the dollar store. In hindsight, I'd have painted the interior of the panels too. Because I wanted to back-light these to make them look like real control panels, I measured out where I wanted them on the sides, and then painted the bottom of where they sit the shiniest silver spray paint I could find, figuring it would help reflect light on the inside. I cut out some of the foam backing from the display they came in and inserted that into the back of 4 of the panels. I simply took a black marker to them, taking care not to colour over where the lights actually flashed. I also had some old flashing LED pins shaped like cowboy hats that were left over from a work event, so I figured if I could add them, I'd have some flashy chase lights for cheap. I needed these to cover the hand-holds punched into the side of the packing box, where I would be lifting Han from the inside. I just asked if I could have them before they threw the display away). I added a couple cheap blinky LEDs to (scavenged from a grocery store cardboard stand up display for batteries. I also add a pair of smaller "panels" that were just cheap drawer organizers from the dollar store painted silver. I also used a spreadsheet program to make some grid patterns to put behind the coloured plastic to make the light shining through seem more like some kind of data screen. I cut out holes of assorted sizes, then glued some cut outs of translucent binder dividers I picked up at the dollar store inside, added spray painted bottle caps for dials, and set them aside. I painted the Hero Panels all silver, while the other four were black with a silver front panel. Again though, this panel in the movie bounced from one side to the other depending on the scene. It's the one with the handles on the side. The only one I really tried to make look like the movie was the "Hero Panel". I also only created 6 of them, as opposed to the 8 in the movies, but with my HIC being shorter, I thought I could get away with it. The one in the photo is not one of the ones I used, and the dimensions are a bit off. Originally made from the dash panels of a 1978 Volvo, I figured the tissue boxes would be cheaper and easier to come by. I found the easiest thing to make these from was empty tissue boxes. Once cut, glued, and painted, only Han would know for sure! As for the shoes, I couldn't find any that I wanted to cut the ends off of until I found some that had been purchased years earlier for a Wizard of Oz group costume that never happened. At this point I also used painters tape to make a border around the edges to keep a distinction between the messy frozen part of Han, and the smooth edges. I recommend using LOTS of hot glue on these, as everyone I encountered wanted to high-5 them. I bent some coat hanger wire to make the fingers bend the way I liked, then stuffed and hot glued those in place. A pair of rubber glove from the dollar store made the hands. I stuffed those with pillow stuffing as it's lightweight and fairly cheap. ![]() After a trip to the thrift shop for clothes (which I bought in grey, in case paint didn't stick as well as I hoped it would), I cut them in half, folded the edges around themselves, and hot glued them to the box, first the shirt, then the pants. Since I really only had one shot at this, I just used a scrap piece of cardboard to make approximate measurements on, adjusted them as needed, then used that as a stencil on the box. Next was figuring out where to put the hole for my face.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |